Bondtech CHT® Coated Brass Nozzle, 1.4 mm

They are manufactured by Bondtech in-house, and will fit the following hotends/blocks: Mosquito® / Magnum Mosquito® Liquid Mosquito® Magnum+ Copperhead™ E3D Chimera and Kraken E3D V4, V5 and V6 blocks Prusa i3, Prusa Mini RepRap M6 Features 1 unit per pack; Available sizes : 0.40, 0.50, 0.60, 0.80, 1.0, 1.4 and 1.8mm; Optimized for 1.75mm filament; Compatible with 2.85mm filament. Requires 6mm wrench Main Bondtech CHT® Advantages Higher melt capacity by increasing the surface area of the heating walls Affordable price Machined with ultra-precision Brass nozzle with Nickel coated surface Follows nozzle standards: RepRap (M6×1×7.5×12.5) MK8 (M6×1×5×13) May be used with 1.75 or 2.85mm hotends. Advantages of the Bondtech CHT® technology: Bondtech CHT® nozzles split the filament into 3 thinner strands allowing to melt the material from within. In doing so, the material melts faster and higher flow rates can be used. Core Heating is a patented technology Registration number: EP3445568A1Nozzles for 3D printers made of metal with at least one or a multitude of holes to increase the surface area of the heating walls. Advantages of the Nickel Coating A Nickel coating is applied to our Coated Brass nozzles to provide protection against corrosion, erosion, and abrasion. Nickel coated nozzles have more corrosion resistance and lower coefficient of friction, which allows slicker feeding of material and delays plastic adhesion to the nozzle's surface.

They are manufactured by Bondtech in-house, and will fit the following hotends/blocks: Mosquito® / Magnum Mosquito® Liquid Mosquito® Magnum+ Copperhead™ E3D Chimera and Kraken E3D V4, V5 and V6 blocks Prusa i3, Prusa Mini RepRap M6 Features 1 unit per pack; Available sizes : 0.40, 0.50, 0.60, 0.80, 1.0, 1.4 and 1.8mm; Optimized for 1.75mm filament; Compatible with 2.85mm filament. Requires 6mm wrench Main Bondtech CHT® Advantages Higher melt capacity by increasing the surface area of the heating walls Affordable price Machined with ultra-precision Brass nozzle with Nickel coated surface Follows nozzle standards: RepRap (M6×1×7.5×12.5) MK8 (M6×1×5×13) May be used with 1.75 or 2.85mm hotends. Advantages of the Bondtech CHT® technology: Bondtech CHT® nozzles split the filament into 3 thinner strands allowing to melt the material from within. In doing so, the material melts faster and higher flow rates can be used. Core Heating is a patented technology Registration number: EP3445568A1Nozzles for 3D printers made of metal with at least one or a multitude of holes to increase the surface area of the heating walls. Advantages of the Nickel Coating A Nickel coating is applied to our Coated Brass nozzles to provide protection against corrosion, erosion, and abrasion. Nickel coated nozzles have more corrosion resistance and lower coefficient of friction, which allows slicker feeding of material and delays plastic adhesion to the nozzle's surface.

Thumbscrew replacement for Bondtech extruder.

Bondtech drive gear kit in hardened and surface protected steel. Precision cnc-machined. Super sharp teeths for maximum grip on the filament. The perfect choice for a high-performance feeding system. Extremely high wear resistance for use with abrasive filaments. These drivegear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 5 mm, secondary gear with two needle bearings, M3x2 setscrew and one 3x20 mm shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. Gear set for filament size 2.85 – 3.0 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. A Lithium based grease is recommended to use on the gear section and inside the needle bearings for low friction and to avoid wear. A small dab of grease is enough.

They are manufactured by Bondtech in-house, and will fit the following hotends/blocks: Mosquito® / Magnum Mosquito® Liquid Mosquito® Magnum+ Copperhead™ E3D Chimera and Kraken E3D V4, V5 and V6 blocks Prusa i3, Prusa Mini RepRap M6 Features 1 unit per pack; Available sizes : 0.40, 0.50, 0.60, 0.80, 1.0, 1.4 and 1.8mm; Optimized for 1.75mm filament; Compatible with 2.85mm filament. Requires 6mm wrench Main Bondtech CHT® Advantages Higher melt capacity by increasing the surface area of the heating walls Affordable price Machined with ultra-precision Brass nozzle with Nickel coated surface Follows nozzle standards: RepRap (M6×1×7.5×12.5) MK8 (M6×1×5×13) May be used with 1.75 or 2.85mm hotends. Advantages of the Bondtech CHT® technology: Bondtech CHT® nozzles split the filament into 3 thinner strands allowing to melt the material from within. In doing so, the material melts faster and higher flow rates can be used. Core Heating is a patented technology Registration number: EP3445568A1Nozzles for 3D printers made of metal with at least one or a multitude of holes to increase the surface area of the heating walls. Advantages of the Nickel Coating A Nickel coating is applied to our Coated Brass nozzles to provide protection against corrosion, erosion, and abrasion. Nickel coated nozzles have more corrosion resistance and lower coefficient of friction, which allows slicker feeding of material and delays plastic adhesion to the nozzle's surface.

Fermio Labs miniature linear guideway; single rail cut to length with a single long block. Highest preload (Z1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. Unlike most of the linear guideways produced in China, our blocks feature a functional injection hole / grease port for lubrication which is compatible with our lubrication kit. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.