Filter
–
Top
ALL
Brass Heat Insert, 5 x 4 mm, M3
Brass heat inserts, specially developed for FDM 3D printed parts and post-insertion.
Content: 100 piece (€0.09* / 1 piece)
€8.99*
Sold out
Top
CPC MR 9ML, 50 mm
Linear Guide / Block / Type: Long | Linear Guide / Rail / Length: 50 mm | Linear Guide / Rail / Width: 9 mm
Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.
€39.99*
Top
Fermio MGN9H, 50 mm, 440C SUS (silver) €14.99*
Linear Guide / Block / Type: Long | Linear Guide / Rail / Length: 50 mm | Linear Guide / Rail / Material: 440C SUS (silver) | Linear Guide / Rail / Width: 9 mm
Fermio Labs miniature linear guideway; single rail cut to length with a single long block. Highest preload (Z1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. Unlike most of the linear guideways produced in China, our blocks feature a functional injection hole / grease port for lubrication which is compatible with our lubrication kit. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.
Variants from €12.99*
Sold out
Tip
Top
V24
TRI
VSW
Fermio OptoTap PCB (12/24 Volt)
Optical sensor PCB for TAP including adapter cable to our wire harness for Plug&Play The design includes a supply polarity and overshoot protection.Technical Data 12V or 24V supply Open drain signal output Optional 10k pull-up (against internal +5V) on signal output (via solder bridge) OPB971N51 sensor Contents 1x full assembled and 100% tested PCB 1x short cable (JST-PH => Molex Microfit 3.0)
€17.99*
Tip
Top
V24
TRI
VSW
Fermio OptoTap PCB (5 Volt)
Optical sensor PCB for TAP including adapter cable to our wire harness for Plug&Play, but you need to ensure 5V supply for this board. The design includes a supply polarity protection. INFO: New version! Warning Do not connect or disconnect the PCB when the printer is powered! Technical Data 5V supply voltage only Open drain signal output Optional 10k pull-up (against +5V) on signal output (via solder bridge) OPB973N51 sensor (signal level is inverted!) Contents 1x full assembled and 100% tested PCB 1x short cable (JST-PH => Molex Microfit 3.0)
€14.99*
> 500 available
Top
ALL
Round Neodym Magnets, 6 x 3 mm, N35H (high temp), electrically conductive €3.99*
Magnet: N35H, silver, uncoated, electrically conductive
Round neodym magnet, 6 x 3 mm, N35H (≤ 100 °C), nickel plated. Note Electrically conductive.
Content: 10 piece (€0.40* / 1 piece)
Variants from €2.99*
> 500 available
Top
ALL
Round Neodym Magnets, 6 x 3 mm, N52, coated black, electrically non conductive
Magnet: N52, black, coated, electrically non conductive
Round neodym magnet, 6 x 3 mm, N52 (≤ 80 °C), epoxy coated black. Note Electrically non conductive.
Content: 10 piece (€0.30* / 1 piece)
€2.99*
Only 3 available
V24
TRI
Voron Tap Printed Parts
Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Note You are buying 3D printed parts only. Any additional hardware shown is for demonstration purposes only.Content1x MGN9_Assembly_Tool1x Printed_Cut_Guide1x Tap_Front_r21x Tap_Magnet_Left_r21x Tap_Magnet_Right_r21x Tap_Upper_PCB_r21x Tap_Center_r6
€25.99*