CPC MR 12ML, 300 mm

Product information "CPC MR 12ML, 300 mm"

Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication and a seal from all sides (even the bottom).

Warranty

The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively.

Cleaning

We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth.

Lubrication

We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order):

Note: lubricants containing MoS2 or graphite must not be used.

Linear Guide / Block / Type: Long
Linear Guide / Rail / Length: 300 mm
Linear Guide / Rail / Width: 12 mm
Voron / Model: Switchwire, Trident, VORON2 V2.4
Voron / Spec: 250
Bill of Materials for "CPC MR 12ML, 300 mm"
Our Bill Of Materials is a usefull tool while sourcing your VORON.
Model / Spec120230250300350
VORON Legacy
VORON Switchwire 4
VORON Trident 1
VORON0 V0.1
VORON1 V1.8
VORON2 V2.4 1

0 of 0 reviews

Leave a review!

Share your experiences with other customers.


GCr15 / Bearing Steel

GCr15 is a very well known and worlwide used bearing steel. For the looks and to improve resistance to rust, we oxidise them black!

440C SUS / Stainless Steel

440C is most famous as one of the best and most versatile cutlery steel. Its very hard, resistant to rust, is good for polishing and in general an overachiever in its area.

Cleaning

Our rails come preserved with oil so they are protected against the elements while waiting for being installed in a new printer. This oil needs to be removed before usage, it's not feasible as lubricant!

Lubrication

We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation.

Preload

Preload determines the stiffness of your linear guide. The higher the preload, the stiffer. Free running rails can wobble which will result in noise and vibrations and visible defects in your overall print quality (i.e. layer stacking). Our rails are specced with the highest preload level available - reducing noise and vibrations and improving your print quality!

Top
OMRON D2F-5L Microswitch
OMRON D2F-5L Microswitch
Endstop Microswitch usable for X/Y/Z. Type: D2F-5LRating: 250 V/AC - 5A

€2.99*
Top
StealthBurner RGB LED Kit
StealthBurner RGB LED Kit
StealthBurner RGB LED Kit, pre-wired. Total of three SK6812 RGBNW LEDs. Wire terminated with 3-pin Molex Microfit 3.0 connector. Hint Use our prepared connection cable StealthBurner RGB LED Wire Harness to update your wire harness. Note The M42 hexnut and 3D printed parts are not part of this kit and are pictured for demonstration purposes only.

€5.99*
Top
Brass Heat Insert, 5 x 4 mm, M3
Brass Heat Insert, 5 x 4 mm, M3
Brass heat inserts, specially developed for FDM 3D printed parts and post-insertion.

Content: 100 piece (€0.09* / 1 piece)

€8.99*
Top
Solid State Relay (SSR), DC/AC, 120/230 V/AC, 10 Ampere
Solid State Relay (SSR), DC/AC, 120/230 V/AC, 10 Ampere
This solid state relay can switch load currents in the range of 24-480VAC (usually 230V) up to currents of 10A. zero cross switching galvanic isolation (opto-isolator) touch protection (IP20) switching state signaling with LED Downloads A-Senco SSR-500-1DA48-10 Datasheet

€14.99*
Top
Voron Nozzle Endstop
Voron Nozzle Endstop
DIY Z Endstop PCB, requires custom printed part and soldering. Contents 1x PCB 1x 3-Pin JST-XH connector 1x Omron D2F-5L Hint Use our prepared connection cable Nozzle Endstop Wire Harness Downloads Z-Switch_FermioLabs_Rev1.stl Note: The pins of the connector and microswitch have to be cutted very flat before soldering!

€4.99*