Top seller
50+
V2.4
V1.8
V0.0
50+
V2.4
V2.4
350
50+
V2.4
300
V2.4
V1.8
300
V2.4
350
50+
V2.4
V1.8
No results were found for the filter!
50+
V2.4
250
DIN Rail 35x7.5mm, 370mm long DIN rail TS35x7.5 - 368mm long. Cut to length burr-free, made from sendzimir galvanized steel. Hole pattern is 25x5.2mm and matches deck panel and aluminium extrusion distances so they can be mounted below the printer.
Content 2 Unit (€2.70 * / 1 Unit)
€5.40 *
50+
V2.4
300
DIN Rail 35x7.5mm, 420mm long DIN rail TS35x7.5 - 418mm long. Cut to length burr-free, made from sendzimir galvanized steel. Hole pattern is 25x5.2mm and matches deck panel and aluminium extrusion distances so they can be mounted below the printer.
Content 2 Unit (€2.80 * / 1 Unit)
€5.60 *
V2.4
350
DIN Rail 35x7.5mm, 470mm long DIN rail TS35x7.5 - 468mm long. Cut to length burr-free, made from sendzimir galvanized steel. Hole pattern is 25x5.2mm and matches deck panel and aluminium extrusion distances so they can be mounted below the printer.
Content 2 Unit (€2.90 * / 1 Unit)
€5.80 *
NEW
50+
50+
V2.4
V1.8
SSR, DC/AC, 230V/AC 10A This solid state relay can switch load currents in the range of 24-480VAC (usually 230V) up to currents of 10A. zero cross switching galvanic isolation (opto-isolator) touch protection (IP20) switching state signaling with LED
Content 1 Unit
€12.90 *
50+
V2.4
V1.8
V0.0
TL-Q5MC2 Inductive Sensor Genuine OMRON TL-Q5MC2 2M NPN NC inductive sensor, suitable as Z probe, with a 5mm sensing distance. Note: does not sense alumium early enough. Requires a springsteel sheet. needs longer screws than the BOM sensor (2x M3x25 instead of...
Content 1 Unit
€49.90 *
V2.4
V1.8
250
VORON2 energy chain, X/Y axis, 250mm spec VORON2 energy chain made by igus®. Matching length for X and Y axis for 250mm spec. Flexible ends. Fully assembled. Note: two needed for a VORON2.
Content 1 Unit
€12.90 *
V2.4
V1.8
300
VORON2 energy chain, X/Y axis, 300mm spec VORON2 energy chain made by igus®. Matching length for X and Y axis for 300mm spec. Flexible ends. Fully assembled. Note: two needed for a VORON2.
Content 1 Unit
€13.90 *
V2.4
350
VORON2 energy chain, X/Y axis, 350mm spec VORON2 energy chain made by igus®. Matching length for X and Y axis for 350mm spec. Flexible ends. Fully assembled. Note: two needed for a VORON2.
Content 1 Unit
€14.90 *
V2.4
250
VORON2 energy chain, Z axis, 250mm spec VORON2 energy chain made by igus®. Matching length for Z axis for 250mm spec. Flexible ends. Fully assembled.
Content 1 Unit
€17.90 *
V2.4
300
VORON2 energy chain, Z axis, 300mm spec VORON2 energy chain made by igus®. Matching length for Z axis for 300mm spec. Flexible ends. Fully assembled.
Content 1 Unit
€18.90 *
V2.4
350
VORON2 energy chain, Z axis, 350mm spec VORON2 energy chain made by igus®. Matching length for Z axis for 350mm spec. Flexible ends. Fully assembled.
Content 1 Unit
€19.90 *
V2.4
XY-Endstop, Hall-Effect Hall effect endstop board for X and Y axis. Fully functional, populated with a JST-XH 4 pin female connector. Includes 2x 6x3mm Neodymium magnets. This single board replaces the two switches on the XY joint as endstops. One needed per...
Content 1 Unit
€14.90 *
Viewed