Filter
–
> 500 available
Top
K3
V24
625 2RS, 5 x 16 x 5 mm, Miniature Deep Groove Ball Bearing
Bearings: 625-2RS
Miniature ball bearings are deep groove ball bearings in small. Their dimensions make them suitable for special applications. In addition, they allow very high speeds with low noise.
€0.99*
Sold out
Top
ALL
Bondtech Drive Gear Set, 1.75 mm Filament, 5 mm Shaft
Bondtech / Drive Gear: 1.75 mm / 5 mm
Bondtech drive gear kit in hardened and surface protected steel. Precision cnc-machined. Super sharp teeths for maximum grip on the filament. The perfect choice for a high-performance feeding system. Extremely high wear resistance for use with abrasive filaments. These drivegear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 5 mm, secondary gear with two needle bearings, M3x2 setscrew and one 3x20 mm shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. Gear set for filament size 2.85 – 3.0 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. A Lithium based grease is recommended to use on the gear section and inside the needle bearings for low friction and to avoid wear. A small dab of grease is enough.
€31.99*
Only 2 available
Bondtech Drive Gear Set, 1.75 mm Filament, 8 mm Shaft
Bondtech / Drive Gear: 1.75 mm / 8 mm
Bondtech drive gear kit in hardened and surface protected steel. Precision cnc-machined. Super sharp teeths for maximum grip on the filament. The perfect choice for a high-performance feeding system. Extremely high wear resistance for use with abrasive filaments. These drivegear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 5 mm, secondary gear with two needle bearings, M3x2 setscrew and one 3x20 mm shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. Gear set for filament size 2.85 – 3.0 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. A Lithium based grease is recommended to use on the gear section and inside the needle bearings for low friction and to avoid wear. A small dab of grease is enough.
€31.99*
Bondtech LGX Steel Drive Train Upgrade Set
Push Harder! Full Steel Ahead! Set of parts made of Hardened Steel to replace the plastic Drive and Main Double Gears on a Bondtech Large Gears eXtruder: LGX; LGX Lite; LGX Lite Mirrored. Recommended to feed Engineering grade thermoplastics. To use our LGX extruders above our default recommendations: with thicker mounting plates; at higher environment temperatures; at higher stepper motor currents. For detailed instructions (installation, usage, etc.) please follow official Bondtech instructions.
€41.49*
Bondtech LGX® Hardened Steel Drive Wheel
Spare part made of Hardened Steel to replace a Drive Wheel on a Bondtech LGX™ Large Gears eXtruder.
€14.99*
ALL
Bondtech LGX® Large Gears eXtruder
The Bondtech LGX® Large Gears eXtruder is the first of our filament feeders using Bondtech’s new Dual Drive Technology based on larger drive gears.
€116.99*
ALL
Bondtech LGX® Lite Extruder (no motor)
Includes full size LGX® Large Gears, maintenance windows and filament tension lever with 3 presets (open; rigid; flexible). Important Use the LGX® Lite only with a 36mm Round stepper motor featuring a 10 teeth motor gear. Stealthburner If you're looking for a really nice Stealthburner mount, checkout this mod: https://github.com/Eytecz/LGX_Lite_Stealthburner_CW2_style_mount/
€68.99*
Only 8 available
Bondtech LGX® Lite Front Plate Voron
Bondtech / Front Plate: Voron
Spare part for the Bondtech LGX® Lite. Front housing made of grey Polyamide without dyeing. Features a wax protective coating and the LGX® Lite BONDTECH sticker.
€6.99*
Sold out
ALL
Bondtech LGX® Lite Large Gears eXtruder
The Bondtech LGX® Lite is a filament feeder based on the LGX® Large Gears eXtruder and uses Bondtech’s new Dual Drive Technology based on larger drive gears. Stealthburner If you're looking for a really nice Stealthburner mount, checkout this mod: https://github.com/Eytecz/LGX_Lite_Stealthburner_CW2_style_mount/
€82.99*
Only 1 available
Bondtech LGX® Primary Gear
Spare part made of self lubricant high temperature plastic to replace a primary gear on a Bondtech LGX™ Large Gears eXtruder.
€5.99*
Only 5 available
Bondtech LGX® Secondary Gear
Spare part made of self lubricant high temperature plastic to replace a secondary gear on a Bondtech LGX™ Large Gears eXtruder.
€4.99*
Sold out
Top
Bondtech Push-Fit ECAS 4 mm
Push-fit ECAS 4mm is a Bondtech Spare Part to use on the BMG Extruder and on the DDS for CR-10S when a replacement is needed. Size 4 mm is used with 1.75 mm filament.
€1.99*
Sold out
Top
ALL
Bondtech Shaft Assembly
Replacement Shaft assembly for our Bondtech Mini Geared (BMG), SingleDirect and DualDirect extruders. It includes the set screw for primary 1.75/5.0 drive gear.Note: New improved revision from Bondtech, where the gear wheel is in white now! For more information see link
€6.99*
Sold out
Top
ALL
Top
ALL
Brass Heat Insert, 5 x 4 mm, M3
Brass heat inserts, specially developed for FDM 3D printed parts and post-insertion.
Content: 100 piece (€0.09* / 1 piece)
€8.99*
Sold out
V24
TRI
VSW
CPC MR 12ML, 300 mm €74.99*
Linear Guide / Block / Type: Long | Linear Guide / Rail / Length: 300 mm | Linear Guide / Rail / Width: 12 mm
Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.
Variants from €39.99*
Sold out
V24
TRI
CPC MR 12ML, 350 mm €79.99*
Linear Guide / Block / Type: Long | Linear Guide / Rail / Length: 350 mm | Linear Guide / Rail / Width: 12 mm
Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.
Variants from €39.99*
Sold out
V24
TRI
CPC MR 12ML, 400 mm €84.99*
Linear Guide / Block / Type: Long | Linear Guide / Rail / Length: 400 mm | Linear Guide / Rail / Width: 12 mm
Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.
Variants from €39.99*
Only 8 available
Top
V02
V01
CPC MR 7ML, 150 mm €44.99*
Linear Guide / Block / Type: Long | Linear Guide / Rail / Length: 150 mm | Linear Guide / Rail / Width: 7 mm
Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.
Variants from €39.99*
ALL
CPC MR 9ML, 300 mm €69.99*
Linear Guide / Block / Type: Long | Linear Guide / Rail / Length: 300 mm | Linear Guide / Rail / Width: 9 mm
Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.
Variants from €39.99*
Sold out
ALL
CPC MR 9ML, 350 mm €74.99*
Linear Guide / Block / Type: Long | Linear Guide / Rail / Length: 350 mm | Linear Guide / Rail / Width: 9 mm
Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.
Variants from €39.99*
Sold out
Top
V24
TRI
CPC MR 9ML, 400 mm €79.99*
Linear Guide / Block / Type: Long | Linear Guide / Rail / Length: 400 mm | Linear Guide / Rail / Width: 9 mm
Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.
Variants from €39.99*
Sold out
CPC MR 9ML, 50 mm
Linear Guide / Block / Type: Long | Linear Guide / Rail / Length: 50 mm | Linear Guide / Rail / Width: 9 mm
Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.
€39.99*
Top
V02
V01
Daylight on a Matchstick (COB)
Daylight / LED: COB | Daylight / Size: SM
COB chainable 24V LED baron both sides a JST-XH 2 pin connector (black)CRI >= 90 CTT = 4000KTypical Luminous Efficacy = 188lm/WTypical Flux @25°CStick XXL2x 660lmStick2x 500lmMatchstick2x 330lmRGB chainable 5V RGB LED baron both sides a JST-XH 3 pin connector (black)WS2812B LEDsone resistor for the dataline is inside each box, in case you need it to get right color controlKlipper color order: GRB Length Stick XXL370mmfor V2/TR 350Stick270mmfor V2/TR 250/300Matchstick158mmfor V0.1/V0.2 Note Based on BLAMM's Daylight Voron Hardware design.
Content: 2 piece (€8.75* / 1 piece)
€17.49*