Product information "Aluminium Plate, 120 x 120 x 6 mm"
Saw cut, precision milled and stress relieved cast aluminium plates. These are meant for DIY enthusiasts who want to create their own build plates. Made from the same raw material we use for our famous build plates!
Properties "Aluminium Plate, 120 x 120 x 6 mm"
EN AW 5083 [AlMg4,5Mn0,7]
Dimension / Thickness:
120 x 120 mm
Tolerance / Flatness:
0.4 mm / m
Tolerance / Thickness:
± 0,10 mm
Manufacturer "Fermio Labs GmbH"
Fermio Labs provides the Voron Design community with high quality products. The founders are deeply rooted in and connected with the community and want to make Voron 3D printers more accessible.
The silicone heatmats were custom designed by Fermio Labs and made to spec by Keenovo. All heaters are optimized for our build plates shapes and hole positions. They allow even heating almost all the way to the edges of the build plate. The power is adjusted to allow running them at 100 % power without risking damage to the build plate instead of the 50% to 80% PWM limit recommended for the heaters listed on the BOM. The standard DIN466 thumb nuts used in all Voron printers used as spacers (VORON2) or levelling nuts (Trident, VORON0 and VORON1) can be used as guides to align the heater. For added safety all heaters come with a self resetting bi-metal 150C thermostat. This turns off the heater if temperatures reaches 150 C due to technical failure of your electronics (only meant as a safety feature, not for temperature regulation). Thermistor used is a NTC 100K thermistor (Beta 25/50 3950K-1%, click here for the R-T datasheet) Choose type 11 or 13 in Marlin firmware. Use "Generic 3950" in Klipper. SKU/Model Compatibility Dimensions Voltage Watt Ampere Thermostat FLG-VRN-KNV-110 VORON0 110 x 110 mm 24 V/DC 60 W 2.5 A 150° C FLG-VRN-KNV-240 250 Trident, VORON1, VORON2 240 x 240 mm 230 V/AC 300 W 1.3 A 150° C FLG-VRN-KNV-290 300 Trident, VORON1, VORON2 290 x 290 mm 230 V/AC 400 W 1.7 A 150° C FLG-VRN-KNV-340 350 Trident, VORON2 340 x 340 mm 230 V/AC 500 W 2.1 A 150° C
The MakerBeamXL T-slot nut is made of stainless steel and was specially designed to slide into the T-slot grooves of the MakerBeamXL profile. The T-slot nut is great to fasten brackets or corner cubes. These T-slot nuts are also compatible with OpenBeam. Both MakerBeamXL and OpenBeam are 15mmx15mm in diameter.
This solid state relay can switch load currents in the range of 24-480VAC (usually 230V) up to currents of 10A. zero cross switching galvanic isolation (opto-isolator) touch protection (IP20) switching state signaling with LED Downloads A-Senco SSR-500-1DA48-10 Datasheet
Tophat panel set made from laser cut acrylic (PMMA) sheets for the VORON0 V0.1. All panels are 3mm thick. You will need to print the updated clips. Contents 2pcs side panels 2pcs front/back panels 1pcs top panel Extra: 1pcs back panel in black aluminium composite Cleaning Note don't use isopropanol or similar! only with water or special PMMA cleaner is allowed Downloads V0.1_Tophat_clips_3mm_panels_FermioLabs_Rev2.stl