Disco on a Stick (RGB)

StealthBurner RGB LED Kit, pre-wired. Total of three SK6812 RGBNW LEDs. Wire terminated with 3-pin Molex Microfit 3.0 connector. Hint Use our prepared connection cable StealthBurner RGB LED Wire Harness to update your wire harness. Note The M42 hexnut and 3D printed parts are not part of this kit and are pictured for demonstration purposes only.

Optical sensor PCB for TAP including adapter cable to our wire harness for Plug&Play (For the 5V version you need to ensure 5V, we are working on some documentation. You can also open a ticket for some help!).INFO: (Updated 5.1.23)  At the moment we deliver a 5V only version and we removed U2 from the PCB. There are some issues with the official design. Even with some intermediat solusions we see remaining risk. Warning Do not connect or disconnect the PCB when the printer is powered! Technical Data 5V supply voltage only Open drain signal output Optional 10k pull-up (against +5V) on signal output (via solder bridge) OPB971N51 sensor Contents 1x full assembled and 100% tested PCB 1x short cable (JST-PH => Molex Microfit 3.0)

COB chainable 24V LED baron both sides a JST-XH 2 pin connector (black)CRI >= 90 CTT = 4000KTypical Luminous Efficacy = 188lm/WTypical Flux @25°CStick XXL2x 660lmStick2x 500lmMatchstick2x 330lmRGB chainable 5V RGB LED baron both sides a JST-XH 3 pin connector (black)WS2812B LEDsone resistor for the dataline is inside each box, in case you need it to get right color controlKlipper color order: GRB Length Stick XXL370mmfor V2/TR 350Stick270mmfor V2/TR 250/300Matchstick158mmfor V0.1/V0.2 Note Based on BLAMM's Daylight Voron Hardware design.

The SUNON MF50151VX-B00U-A99 is suitable for Nevermore Micro V4 and V5 Duo. Note The fan comes without any connectors, just bare wires. Contents 1 pcs of SUNON MF50151VX-B00U-A99

Note #1: the wire harness is compatible with VORON Trident and VORON1 V1.8, but marketed as VORON2 V2.4 wire harness. Note #2: For the BTT Octopus you can, optionally / as a fallback, use the SKR wire harness. All required JST-XH connectors are included to do the minor modifications. See our adjustment guide for a conversion. Note #3: The LED wires for StealthBurner are not included and have to be bought separately. Are you still crimping or already printing? If you hate bad crimps and realizing how bad your eye sight really is, we have a solution! We're happy to announce that we're the first source worldwide ever for a ready made drop in wire harness using only the highest quality components available: Drop in ready wire harness for VORON2 V2.4 using 2x BTT SKR 1.3/1.4, 1x BTT Octopus or 1x FYSETC Spider MCUs (one JST connector change required for SKR 1.3) Wire harness 100% made in Germany by a well known wire harness manufacturer. All wires are black Helukabel Heluflon®-fep-6y 0.5mm² for the hotend heater and 0.25 mm² for everything else. Some even call these wires the mother of all cables! Only geniune JST and Molex connectors, crimped with professional dies on semi automatic industrial machines. To keep it black, without distracting white labels, all connectors are directly printed with the function. Black is the new orange! Black/red color coding on both ends for all V+ and V- wires. SKR-Variant: BAT85 Diode already included into the probe signal wire. A and B motor connectors for most common motors with detatchable wires and JST-PH 6 pin connectors X/Y-Endstop prepared for 4 pin JST-XH connector. We recommend our compatible Hall Endstop board or the Microswitch PCB, both with JST-XH connector. All wires at the X carriage terminated with Molex Microfit 3.0 connectors (yes, they fit below the stock cable cover) Sufficient wire length for proper wire management under the skirt.

X/Y Hall Effect endstop for contactless end position triggering. The endstop is plug&play for our Wire Harness! Contents 1x Hall Effect Endstop, ready and 100% tested 2x 6x3mm black N52 magnets NoteYou need a different print part from the release ([a]_endstop_pod_hall_effect.stl)