Fermio MGN12H, 400 mm, 440C SUS (silver)

Fermio Labs miniature linear guideway; single rail cut to length with a single long block. Highest preload (Z1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. Unlike most of the linear guideways produced in China, our blocks feature a functional injection hole / grease port for lubrication which is compatible with our lubrication kit. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.

StealthBurner RGB LED Kit, pre-wired. Total of three SK6812 RGBNW LEDs. Wire terminated with 3-pin Molex Microfit 3.0 connector. Hint Use our prepared connection cable StealthBurner RGB LED Wire Harness to update your wire harness. Note The M42 hexnut and 3D printed parts are not part of this kit and are pictured for demonstration purposes only.

The silicone heatmats were custom designed by Fermio Labs and made to spec by Keenovo. All heaters are optimized for our build plates shapes and hole positions. They allow even heating almost all the way to the edges of the build plate. The power is adjusted to allow running them at 100 % power without risking damage to the build plate instead of the 50% to 80% PWM limit recommended for the heaters listed on the BOM. The standard DIN466 thumb nuts used in all Voron printers used as spacers (VORON2) or levelling nuts (Trident, VORON0 and VORON1) can be used as guides to align the heater. For added safety all heaters come with a self resetting bi-metal 150C thermostat. This turns off the heater if temperatures reaches 150 C due to technical failure of your electronics (only meant as a safety feature, not for temperature regulation). Thermistor used is a NTC 100K thermistor (Beta 25/50 3950K-1%, click here for the R-T datasheet) Choose type 11 or 13 in Marlin firmware. Use "Generic 3950" in Klipper. SKU/Model Compatibility Dimensions Voltage Watt Ampere Thermostat FLG-VRN-KNV-110 VORON0 110 x 110 mm 24 V/DC 60 W 2.5 A 150° C FLG-VRN-KNV-240 250 Trident, VORON1, VORON2 240 x 240 mm 230 V/AC 300 W 1.3 A 150° C FLG-VRN-KNV-290 300 Trident, VORON1, VORON2 290 x 290 mm 230 V/AC 400 W 1.7 A 150° C FLG-VRN-KNV-340 350 Trident, VORON2 340 x 340 mm 230 V/AC 500 W 2.1 A 150° C

Adapter plate for mounting an SSR relay on a top-hat rail. Full metal anodized with spring claw.

Genuine igus® e-chain® energy chain, series E2.15.10.028.0. Inner radius of 28mm. Flexible ends. Fully assembled. Opens to the outside. Suiteable for Z axis.

DIN rail TS35x7.5. Cut to length burr-free, made from sendzimir galvanized steel. Hole pattern is 25x5.2mm and matches deck panel and aluminium extrusion distances so they can be mounted below the printer.