IWISS IWS-2210H Crimping Plier

Snap-in Keystone Modulesuitable for standard keystone panels and outletsConnections: USB-A female to USB-A femaleApplication: USB 3.0 cablingMaterial: Nickel-plated contact, thermoplastic housingDimension: 35 x 14,5 x 16,7 mmColor: Black

A Mitutoyo digital caliper equipped with standard outside and inside jaws. Hardened stainless steel construction and equipped with the latest electromagnetic ABSOLUTE AOS System scale for error free, high-speed measurement.

Direct replacement for GE5C spherical bearings. igubal® spherical bearings The use of spherical bearings is usually associated with high weight bearing materials, difficult installation, and high costs. Most of the time, maintenance is still necessary over the long-term, and the bearings are only corrosion-resistant in special designs. Often roller bearings or plain bearings malfunction prematurely due to high edge loads, or because they need to be elaborately readjusted, reamed, or refitted in order to compensate for alignment errors. igubal® spherical bearings put an end to all of these disadvantages and open up many new possibilities for your engineering design: they are easy to handle, cost-effective, lightweight and robust. The housing is made from igumid G, an extremely impact-resistant, long-fibre-reinforced polymer. Suitable for temperatures from -30 °C to +80 °C in long-term use. In standard spherical bearings, the spherical ball is made from iglidur® W300 material, which is known for lowest coefficients of friction in dry operation and extremely low tendency to stick-slip. This is especially important for low loads and very slow movements. Compensation of misalignment and edge loads Corrosion-resistant High vibration-dampening Excellent vibration dampening Suitable for rotating, oscillating and axial movements Tolerances Maintenance-free igubal® spherical bearings have a tolerance in the inner diameter of E10. The shaft tolerance should be between h6 and h9. The bearing clearance allows for expansion of the bearings due to increasing temperatures. Assembly igubal® spherical bearings are press-fitted into a recommended H7 housing bore and axially secured. Exact alignment of the bearing housing is not necessary since the spherical bearing automatically compensates for alignment errors.

Fermio Labs miniature linear guideway; single rail cut to length with a single long block. Highest preload (Z1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. Unlike most of the linear guideways produced in China, our blocks feature a functional injection hole / grease port for lubrication which is compatible with our lubrication kit. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.

Optical sensor PCB for TAP including adapter cable to our wire harness for Plug&Play, but you need to ensure 5V supply for this board. The design includes a supply polarity protection. INFO: New version! Warning Do not connect or disconnect the PCB when the printer is powered! Technical Data 5V supply voltage only Open drain signal output Optional 10k pull-up (against +5V) on signal output (via solder bridge) OPB973N51 sensor (signal level is inverted!) Contents 1x full assembled and 100% tested PCB 1x short cable (JST-PH => Molex Microfit 3.0)

StealthBurner RGB LED Kit, pre-wired. Total of three SK6812 RGBNW LEDs. Wire terminated with 3-pin Molex Microfit 3.0 connector. Hint Use our prepared connection cable StealthBurner RGB LED Wire Harness to update your wire harness. Note The M42 hexnut and 3D printed parts are not part of this kit and are pictured for demonstration purposes only.