Solid State Relay (SSR), DC/AC, 120/230 V/AC, 10 Ampere

DIN rail TS35x7.5. Cut to length burr-free, made from sendzimir galvanized steel. Hole pattern is 25x5.2mm and matches deck panel and aluminium extrusion distances so they can be mounted below the printer.

DIN rail TS35x7.5. Cut to length burr-free, made from sendzimir galvanized steel. Hole pattern is 25x5.2mm and matches deck panel and aluminium extrusion distances so they can be mounted below the printer.

DIN rail TS35x7.5. Cut to length burr-free, made from sendzimir galvanized steel. Hole pattern is 25x5.2mm and matches deck panel and aluminium extrusion distances so they can be mounted below the printer.

Adapter plate for mounting an SSR relay on a top-hat rail. Full metal anodized with spring claw.

This solid state relay can switch load currents in the range of 24-480VAC (usually 230V) up to currents of 10A. zero cross switching galvanic isolation (opto-isolator) touch protection (IP20) switching state signaling with LED Downloads A-Senco SSR-500-1DA48-10 Datasheet

The silicone heatmats were custom designed by Fermio Labs and made to spec by Keenovo. All heaters are optimized for our build plates shapes and hole positions. They allow even heating almost all the way to the edges of the build plate. The power is adjusted to allow running them at 100 % power without risking damage to the build plate instead of the 50% to 80% PWM limit recommended for the heaters listed on the BOM. The standard DIN466 thumb nuts used in all Voron printers used as spacers (VORON2) or levelling nuts (Trident, VORON0 and VORON1) can be used as guides to align the heater. For added safety all heaters come with a self resetting bi-metal 150C thermostat. This turns off the heater if temperatures reaches 150 C due to technical failure of your electronics (only meant as a safety feature, not for temperature regulation). Thermistor used is a NTC 100K thermistor (Beta 25/50 3950K-1%, click here for the R-T datasheet) Choose type 11 or 13 in Marlin firmware. Use "Generic 3950" in Klipper. SKU/Model Compatibility Dimensions Voltage Watt Ampere Thermostat FLG-VRN-KNV-110 VORON0 110 x 110 mm 24 V/DC 60 W 2.5 A 150° C FLG-VRN-KNV-240 250 Trident, VORON1, VORON2 240 x 240 mm 230 V/AC 300 W 1.3 A 150° C FLG-VRN-KNV-290 300 Trident, VORON1, VORON2 290 x 290 mm 230 V/AC 400 W 1.7 A 150° C FLG-VRN-KNV-340 350 Trident, VORON2 340 x 340 mm 230 V/AC 500 W 2.1 A 150° C

The silicone heatmats were custom designed by Fermio Labs and made to spec by Keenovo. All heaters are optimized for our build plates shapes and hole positions. They allow even heating almost all the way to the edges of the build plate. The power is adjusted to allow running them at 100 % power without risking damage to the build plate instead of the 50% to 80% PWM limit recommended for the heaters listed on the BOM. The standard DIN466 thumb nuts used in all Voron printers used as spacers (VORON2) or levelling nuts (Trident, VORON0 and VORON1) can be used as guides to align the heater. For added safety all heaters come with a self resetting bi-metal 150C thermostat. This turns off the heater if temperatures reaches 150 C due to technical failure of your electronics (only meant as a safety feature, not for temperature regulation). Thermistor used is a NTC 100K thermistor (Beta 25/50 3950K-1%, click here for the R-T datasheet) Choose type 11 or 13 in Marlin firmware. Use "Generic 3950" in Klipper. SKU/Model Compatibility Dimensions Voltage Watt Ampere Thermostat FLG-VRN-KNV-110 VORON0 110 x 110 mm 24 V/DC 60 W 2.5 A 150° C FLG-VRN-KNV-240 250 Trident, VORON1, VORON2 240 x 240 mm 230 V/AC 300 W 1.3 A 150° C FLG-VRN-KNV-290 300 Trident, VORON1, VORON2 290 x 290 mm 230 V/AC 400 W 1.7 A 150° C FLG-VRN-KNV-340 350 Trident, VORON2 340 x 340 mm 230 V/AC 500 W 2.1 A 150° C

The silicone heatmats were custom designed by Fermio Labs and made to spec by Keenovo. All heaters are optimized for our build plates shapes and hole positions. They allow even heating almost all the way to the edges of the build plate. The power is adjusted to allow running them at 100 % power without risking damage to the build plate instead of the 50% to 80% PWM limit recommended for the heaters listed on the BOM. The standard DIN466 thumb nuts used in all Voron printers used as spacers (VORON2) or levelling nuts (Trident, VORON0 and VORON1) can be used as guides to align the heater. For added safety all heaters come with a self resetting bi-metal 150C thermostat. This turns off the heater if temperatures reaches 150 C due to technical failure of your electronics (only meant as a safety feature, not for temperature regulation). Thermistor used is a NTC 100K thermistor (Beta 25/50 3950K-1%, click here for the R-T datasheet) Choose type 11 or 13 in Marlin firmware. Use "Generic 3950" in Klipper. SKU/Model Compatibility Dimensions Voltage Watt Ampere Thermostat FLG-VRN-KNV-110 VORON0 110 x 110 mm 24 V/DC 60 W 2.5 A 150° C FLG-VRN-KNV-240 250 Trident, VORON1, VORON2 240 x 240 mm 230 V/AC 300 W 1.3 A 150° C FLG-VRN-KNV-290 300 Trident, VORON1, VORON2 290 x 290 mm 230 V/AC 400 W 1.7 A 150° C FLG-VRN-KNV-340 350 Trident, VORON2 340 x 340 mm 230 V/AC 500 W 2.1 A 150° C